Evaggelos Balaskas - System Engineer

Hardware Details

HP ProLiant MicroServer
AMD Turion(tm) II Neo N54L Dual-Core Processor
Memory Size: 2 GB - DIMM Speed: 1333 MT/s
Maximum Capacity: 8 GB

Running 24×7 from 23/08/2010, so nine years!

Prologue

The above server started it’s life on CentOS 5 and ext3. Re-formatting to run CentOS 6.x with ext4 on 4 x 1TB OEM Hard Disks with mdadm raid-5. That provided 3 TB storage with Fault tolerance 1-drive failure. And believe me, I used that setup to zeroing broken disks or replacing faulty disks.

As we are reaching the end of CentOS 6.x and there is no official dist-upgrade path for CentOS, and still waiting for CentOS 8.x, I made decision to switch to Ubuntu 18.04 LTS. At that point this would be the 3rd official OS re-installation of this server. I chose ubuntu so that I can dist-upgrade from LTS to LTS.

This is a backup server, no need for huge RAM, but for a reliable system. On that storage I have 2m files that in retrospect are not very big. So with the re-installation I chose to use xfs instead of ext4 filesystem.

I am also running an internal snapshot mechanism to have delta for every day and that pushed the storage usage to 87% of the 3Tb. If you do the math, 2m is about 1.2Tb usage, we need a full initial backup, so 2.4Tb (80%) and then the daily (rotate) incremental backups are ~210Mb per day. That gave me space for five (5) daily snapshots aka a work-week.

To remove this impediment, I also replaced the disks with WD Red Pro 6TB 7200rpm disks, and use raid-1 instead of raid-5. Usage is now ~45%

Problem

Frozen System

From time to time, this very new, very clean, very reliable system froze to death!

When attached monitor & keyboard no output. Strange enough I can ping the network interfaces but I can not ssh to the server or even telnet (nc) to ssh port. Awkward! Okay - hardware cold reboot then.

As this system is remote … in random times, I need to ask from someone to cold-reboot this machine. Awkward again.

Kernel Panic

If that was not enough, this machine also has random kernel panics.

Errors

Let’s start troubleshooting this system

# journalctl -p 3 -x

Important Errors

ERST: Failed to get Error Log Address Range.
APEI: Can not request [mem 0x7dfab650-0x7dfab6a3] for APEI BERT registers
ipmi_si dmi-ipmi-si.0: Could not set up I/O space

and more important Errors:

INFO: task kswapd0:40 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task xfsaild/dm-0:761 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task kworker/u9:2:3612 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task kworker/1:0:5327 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task rm:5901 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task kworker/u9:1:5902 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task kworker/0:0:5906 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task kswapd0:40 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task xfsaild/dm-0:761 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
INFO: task kworker/u9:2:3612 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.

First impressions ?

BootOptions

After a few (hours) of internet research the suggestion is to disable

• ACPI stands for Advanced Configuration and Power Interface.
• APIC stands for Advanced Programmable Interrupt Controller.

This site is very helpful for ubuntu, although Red Hat still has a huge advanced on describing kernel options better than canonical.

Grub

# vim /etc/default/grub
GRUB_CMDLINE_LINUX="noapic acpi=off"

then

# update-grub
Sourcing file `/etc/default/grub'
Sourcing file `/etc/default/grub.d/50-curtin-settings.cfg'
Generating grub configuration file ...
Found linux image: /boot/vmlinuz-4.15.0-54-generic
Found initrd image: /boot/initrd.img-4.15.0-54-generic
Found linux image: /boot/vmlinuz-4.15.0-52-generic
Found initrd image: /boot/initrd.img-4.15.0-52-generic
done

Verify

# grep noapic /boot/grub/grub.cfg | head -1

        linux   /boot/vmlinuz-4.15.0-54-generic root=UUID=0c686739-e859-4da5-87a2-dfd5fcccde3d ro noapic acpi=off maybe-ubiquity

reboot and check again:

#  journalctl -p 3 -xb
-- Logs begin at Thu 2019-03-14 19:26:12 EET, end at Wed 2019-07-03 21:31:08 EEST. --
Jul 03 21:30:49 servertwo kernel: ipmi_si dmi-ipmi-si.0: Could not set up I/O space

okay !!!

ipmi_si

Unfortunately I could not find anything useful regarding

# dmesg | grep -i ipm
[   10.977914] ipmi message handler version 39.2
[   11.188484] ipmi device interface
[   11.203630] IPMI System Interface driver.
[   11.203662] ipmi_si dmi-ipmi-si.0: ipmi_platform: probing via SMBIOS
[   11.203665] ipmi_si: SMBIOS: mem 0x0 regsize 1 spacing 1 irq 0
[   11.203667] ipmi_si: Adding SMBIOS-specified kcs state machine
[   11.203729] ipmi_si: Trying SMBIOS-specified kcs state machine at mem address 0x0, slave address 0x20, irq 0
[   11.203732] ipmi_si dmi-ipmi-si.0: Could not set up I/O space

# ipmitool list
Could not open device at /dev/ipmi0 or /dev/ipmi/0 or /dev/ipmidev/0: No such file or directory

# lsmod | grep -i ipmi
ipmi_si                61440  0
ipmi_devintf           20480  0
ipmi_msghandler        53248  2 ipmi_devintf,ipmi_si

blocked for more than 120 seconds.

But let’s try to fix the timeout warnings:

INFO: task kswapd0:40 blocked for more than 120 seconds.
      Not tainted 4.15.0-54-generic #58-Ubuntu
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message

if you search online the above message, most of the sites will suggest to tweak dirty pages for your system.

This is the most common response across different sites:

This is a know bug. By default Linux uses up to 40% of the available memory for file system caching. After this mark has been reached the file system flushes all outstanding data to disk causing all following IOs going synchronous. For flushing out this data to disk this there is a time limit of 120 seconds by default. In the case here the IO subsystem is not fast enough to flush the data withing 120 seconds. This especially happens on systems with a lot of memory.

Okay this may be the problem but we do not have a lot of memory, only 2GB RAM and 2GB Swap. But even then, our vm.dirty_ratio = 20 setting is 20% instead of 40%.

But I have the ability to cross-check ubuntu 18.04 with CentOS 6.10 to compare notes:

ubuntu 18.04

# uname -r
4.15.0-54-generic

# sysctl -a | egrep -i  'swap|dirty|raid'|sort
dev.raid.speed_limit_max = 200000
dev.raid.speed_limit_min = 1000
vm.dirty_background_bytes = 0
vm.dirty_background_ratio = 10
vm.dirty_bytes = 0
vm.dirty_expire_centisecs = 3000
vm.dirty_ratio = 20
vm.dirtytime_expire_seconds = 43200
vm.dirty_writeback_centisecs = 500
vm.swappiness = 60

CentOS 6.11

#  uname -r
2.6.32-754.15.3.el6.centos.plus.x86_64

# sysctl -a | egrep -i  'swap|dirty|raid'|sort
dev.raid.speed_limit_max = 200000
dev.raid.speed_limit_min = 1000
vm.dirty_background_bytes = 0
vm.dirty_background_ratio = 10
vm.dirty_bytes = 0
vm.dirty_expire_centisecs = 3000
vm.dirty_ratio = 20
vm.dirty_writeback_centisecs = 500
vm.swappiness = 60

Scheduler for Raid

This is the best online documentation on the
optimize raid

Comparing notes we see that both systems have the same settings, even when the kernel version is a lot different, 2.6.32 Vs 4.15.0 !!!

Researching on raid optimization there is a note of kernel scheduler.

Ubuntu 18.04

# for drive in {a..c}; do cat /sys/block/sd${drive}/queue/scheduler; done

noop deadline [cfq]
noop deadline [cfq]
noop deadline [cfq] 

CentOS 6.11

# for drive in {a..d}; do cat /sys/block/sd${drive}/queue/scheduler; done

noop anticipatory deadline [cfq]
noop anticipatory deadline [cfq]
noop anticipatory deadline [cfq]
noop anticipatory deadline [cfq] 

Anticipatory scheduling

CentOS supports Anticipatory scheduling on the hard disks but nowadays anticipatory scheduler is not supported in modern kernel versions.

That said, from the above output we can verify that both systems are running the default scheduler cfq.

Disks

Ubuntu 18.04

• Western Digital Red Pro WDC WD6003FFBX-6

# for i in sd{b..c} ; do hdparm -Tt  /dev/$i; done

/dev/sdb:
 Timing cached reads:   2344 MB in  2.00 seconds = 1171.76 MB/sec
 Timing buffered disk reads: 738 MB in  3.00 seconds = 245.81 MB/sec

/dev/sdc:
 Timing cached reads:   2264 MB in  2.00 seconds = 1131.40 MB/sec
 Timing buffered disk reads: 774 MB in  3.00 seconds = 257.70 MB/sec

CentOS 6.11

• Seagate ST1000DX001

/dev/sdb:
 Timing cached reads:   2490 MB in  2.00 seconds = 1244.86 MB/sec
 Timing buffered disk reads: 536 MB in  3.01 seconds = 178.31 MB/sec

/dev/sdc:
 Timing cached reads:   2524 MB in  2.00 seconds = 1262.21 MB/sec
 Timing buffered disk reads: 538 MB in  3.00 seconds = 179.15 MB/sec

/dev/sdd:
 Timing cached reads:   2452 MB in  2.00 seconds = 1226.15 MB/sec
 Timing buffered disk reads: 546 MB in  3.01 seconds = 181.64 MB/sec

So what I am missing ?

My initial personal feeling was the low memory. But after running a manual rsync I’ve realized that:

cpu

was load average: 0.87, 0.46, 0.19

mem

was (on high load), when hit 40% of RAM, started to use swap.

KiB Mem :  2008464 total,    77528 free,   635900 used,  1295036 buff/cache
KiB Swap:  2097148 total,  2096624 free,      524 used.  1184220 avail Mem 

So I tweaked a bit the swapiness and reduce it from 60% to 40%

and run a local snapshot (that is a bit heavy on the disks) and doing an upgrade and trying to increase CPU load. Still everything is fine !

I will keep an eye on this story.

Working with VPS (Virtual Private Server), sometimes means that you dont have a lot of memory.

That’s why, we use the swap partition, a system partition that our linux kernel use as extended memory. It’s slow but necessary when your system needs more memory. Even if you dont have any free partition disk, you can use a swap file to add to your linux system.

Create the Swap File

[root@centos7] # dd if=/dev/zero of=/swapfile count=1000 bs=1MiB
1000+0 records in
1000+0 records out
1048576000 bytes (1.0 GB) copied, 3.62295 s, 289 MB/s

[root@centos7] # du -sh /swapfile
1.0G    /swapfile

That is 1G file

Make Swap

[root@centos7] # mkswap -L swapfs /swapfile
Setting up swapspace version 1, size = 1048572 KiB
LABEL=swapfs, UUID=d8af8f19-5578-4c8e-b2b1-3ff57edb71f9

Permissions

[root@centos7] # chmod 0600 /swapfile

Activate

[root@centos7] # swapon /swapfile

Check

# free
              total        used        free      shared  buff/cache   available
Mem:        1883716     1613952       79172       54612      190592       64668
Swap:       1023996           0     1023996

fstab

Now for the final step, we need to edit /etc/fstab

/swapfile   swap    swap    defaults    0   0